Trucks

Gen 3 Ford F-150 Raptor Suspension Upgrades With SDi E-CLIK Pro and Trailing Arms

Gen 3 Ford F-150 Raptor Suspension Upgrades With SDi E-CLIK Pro and Trailing Arms

We’ve used our 2022 Ford F-150 Raptor to tow and to explore trails we’d normally ride in a side-by-side. On Sedona’s Broken Arrow Trail, we spent most of the drive in low range, and the truck’s width was most noticeable in the tight sections. In our Raptor Air Lift towing and off-road test, rear air springs gave us more support with a trailer, and we could feel the change in the rear suspension when we took the truck back off-road.

Those are different jobs for the same truck, and they’re a good starting point for looking at two Gen 3 Raptor upgrades from Suspension Direct Inc. (SDi). The E-CLIK Pro system gives the driver more control over the factory FOX shocks. SDi’s upper and lower rear trailing arms replace the links that help locate the rear axle and use rebuildable joints.

What Ford put under the Gen 3 Raptor

Ford’s third-generation Raptor introduced a five-link, coil-spring rear suspension with a solid axle. Four longitudinal links help control fore-and-aft axle movement and axle rotation under acceleration and braking. A Panhard rod locates the axle side to side. The factory FOX Live Valve shocks electronically vary compression damping as the truck moves. It’s an evolution of the long-travel truck Ford developed around desert terrain, a story that goes back to the Raptor prototype’s run at the Baja 1000.

SDi E-CLIK Pro adds more control over the factory FOX shocks

The SDi E-CLIK Pro system for the Gen 3 Raptor uses the truck’s existing FOX Live Valve shocks and gives the driver a dedicated touchscreen for suspension settings. SDi says the factory drive and steering modes remain functional. The kit is listed at $2,200, with shock revalving available as an option.

SDi E-CLIK Pro electronics, touchscreen and wiring harnesses for the Gen 3 Ford F-150 Raptor
The Gen 3 Raptor E-CLIK Pro system.
  • Trail prioritizes ride comfort on slower, uneven terrain.
  • Street balances ride comfort and body control on pavement.
  • Desert is tuned for faster driving over rough terrain and repeated bumps.

The Pro menu lets you adjust front and rear damping independently and fine-tune how the system responds to pitch, roll, steering, throttle and braking. That gives a Raptor owner a way to tailor how the truck reacts when slowing for a dip, turning into a corner or driving through a stretch of whoops.

What the rear payload setting does when towing a UTV

E-CLIK Pro also has a rear payload setting that lets the driver adjust the damping response for bed cargo or a trailer. For someone who uses a Raptor to haul a side-by-side and then drives the truck off-road after unloading, that’s one of the more relevant features. The Air Lift springs we tested added rear spring support under load. E-CLIK’s payload setting changes how the shocks control suspension movement. Ford’s tow and payload ratings still apply.

E-CLIK Pro fitment: SDi lists this kit for 2021+ Gen 3 Ford F-150 Raptors and the 2023 Raptor R, “Single Live Valve Only.”

SDi rear trailing arms use rebuildable RockJock joints

The SDi Gen 3 Raptor and Raptor R trailing arm set replaces the upper and lower rear links with bolt-on arms machined from 7075-T651 aluminum. The set uses rebuildable RockJock Johnny Joints and includes installation hardware. SDi lists the set at $3,499.99 in black anodized or raw finish.

SDi upper and lower trailing arms for the Gen 3 Ford Raptor
SDi’s upper and lower rear trailing arm set.

For a truck that regularly sees rough dirt roads, rocks or desert use, the joints are the feature I’d pay the most attention to. The RockJock Johnny Joints use urethane bushings, can be greased, and can be rebuilt when they wear. In the video below, SDi says it chose them after hearing from Raptor owners about noise and feedback from conventional uniball trailing arms. SDi also says it tested the arms for more than a year, including running Vegas to Reno and prerunning the Mint 400 course.

Trailing-arm fitment covers the Gen 3 F-150 Raptor and Raptor R according to SDi’s listing. Confirm your specific model year and configuration with SDi before ordering.

Which upgrade makes sense for your Raptor?

If I were choosing between the two for our 2022 Raptor, I’d look at E-CLIK Pro first. The ability to adjust damping from the cab fits the way we use the truck, from towing on pavement to crawling along a trail in low range. The trailing arms are the more targeted purchase for an owner who wants heavy-duty rear links with joints they can rebuild after years of hard off-road use.

Gen 3 Ford F-150 Raptor Suspension Upgrades With SDi E-CLIK Pro and Trailing Arms (3)

Leave a Reply

Your email address will not be published. Required fields are marked *